A Drill Result's Headline Number Is Rarely Its True Width
"42 metres of 3.1 g/t gold" is almost never 42 metres of rock perpendicular to the mineralized zone. It is the length of core the drill bit passed through — the down-hole, or apparent, width. Unless the hole crossed the structure at a right angle, the true width is smaller, and National Instrument 43-101 requires the issuer to say so, or say explicitly that true width is not yet known[^1]. A headline that skips this distinction, or multiplies grade by the apparent length into a gram-metre figure, can overstate the result — sometimes materially, as a Canadian issuer found out the hard way in 2018[^2].
Why apparent width overstates the number
A drill hole is a straight line through rock; a mineralized zone is a plane (or envelope) at some dip and azimuth of its own. If the hole crosses that plane at a shallow angle instead of head-on, the core records a longer intersection than the zone's actual thickness — the same way a knife held flat against a book slices a longer, thinner wedge than a cut straight down through the spine. The true width is the apparent width multiplied by the sine of the angle between the hole and the plane; at a 30-degree crossing angle that factor is 0.5, so a reported 42-metre intersection could be a 21-metre zone. Without a wireframe model of the structure's own orientation, that angle — and therefore the true width — is often not known precisely on the day a drill result is announced, especially early in a program when only a handful of holes exist.
What the rule actually requires
NI 43-101 Section 3.3 governs written disclosure of exploration results, including news releases, and requires more than the assay number. Where an issuer discloses sample or analytical results on a project material to it, the disclosure must include: drill-hole location, azimuth, dip, and depth of interval; a summary of widths and true widths where known — and, where true width is not known, a statement that it is not known; the results of any significantly higher-grade sub-interval contained within a lower-grade intersection, not just the blended average across the full length; factors that could affect accuracy or reliability, such as core-recovery issues; and a description of sample preparation, analysis, security, and the laboratory used[^1]. None of this is optional stylistic detail — it is what separates a compliant drill result from a press release that merely sounds like one. A Qualified Person must review or prepare the disclosure before it goes out.
When it goes wrong: Sun Metals, 2018
On October 25, 2018, Sun Metals Corp. announced drill results from its Stardust Project in north-central British Columbia, describing the intercepts as the "thickest and richest mineralization ever intersected at the project" and disclosing grade-times-length (gram-metre) figures for three holes. The next day, at the request of the Investment Industry Regulatory Organization of Canada, the company retracted both the superlative language and the gram-metre calculations: because the true widths of those intersections were not known, multiplying grade by the down-hole intersected length would overstate the calculation, and the company acknowledged the overstatement could be material[^2]. The underlying assay values were not wrong — the arithmetic built on top of an unverified width was.
Not a one-off
The Sun Metals case is a sharp illustration, not an isolated one. In 2015, the British Columbia Securities Commission, the Ontario Securities Commission, and the Autorité des marchés financiers jointly reviewed the website investor presentations of 130 mining issuers against NI 43-101's disclosure standard. Only 18% were found substantially compliant; 25% showed major non-compliance. Conflating true width with apparent width, without flagging the distinction, was named as one of the recurring problems[^3]. That finding is now a decade old, and it covers investor presentations rather than news releases specifically — but the disclosure rule it was measured against, Section 3.3, has not changed on this point since, so the failure mode it documented is still the one to check for today.
What this means for coverage
Before treating a drill-result headline as decision-grade, three things are checkable directly in the release: does it state a true width, or explicitly say true width is unknown, rather than silently reporting only the down-hole length; does it disclose any higher-grade sub-interval separately, rather than hiding it inside one blended average over a longer length; and does it name the Qualified Person along with basic QA/QC — certified standards, blanks, duplicates, and the laboratory — rather than asserting the grade with no stated verification path. A release missing all three isn't necessarily wrong, but it is reporting less than the rule requires, and the gap is exactly where a headline number and the actual size of a discovery can part ways.
When Mineralis ingests a drill-result disclosure, true width, QA/QC detail, and the signing Qualified Person are recorded as structured fields against the filing — so a gap in what the release actually stated shows up as a gap, not as a number treated with more confidence than the source document itself claims.
References
- Canadian Securities Administrators / Ontario Securities Commission, National Instrument 43-101 — Standards of Disclosure for Mineral Projects, Section 3.3 ("Disclosure of Exploration Information"), current form from the June 30, 2011 amendments, in force as of this writing. Scope: written disclosure, including news releases, by issuers reporting to Canadian securities regulators.
- Sun Metals Corp., "Retraction and Clarification of Disclosure in [the] October 25, 2018 News Release," issued October 26, 2018 at the request of the Investment Industry Regulatory Organization of Canada. Scope: a single company, the Stardust Project (Canyon Creek Skarn Zone, British Columbia), and three specific drill holes (DDH18-SD-412, DDH18-SD-417, DDH18-DS-421); not a statement about any other issuer.
- British Columbia Securities Commission, Ontario Securities Commission, and Autorité des marchés financiers, CSA Staff Notice 43-309 — Review of Website Investor Presentations by Mining Issuers, published April 9, 2015. Scope: website investor presentations of 130 mining issuers reviewed in the three Principal Mining Jurisdictions; findings are specific to that sample and that disclosure channel, and the review is now a decade old.
Request beta access.
Mineralis is currently in Private Beta. Family offices, independent analysts, and mining investors are being invited in waves.
Join the beta waitlist →